Curtain rod guide

Measure your window, choose the right rod and install it in an afternoon.

How to measure

Measure your window

Measure the width of your window, including frame, from edge to edge.
Add 20 cm (8") to that width: 10 cm (4") on each side of the frame.
Choose the rod size whose range includes your total.

Example: a 122 cm (48") window plus 20 cm (8") is 142 cm (56"), so choose the 76-213 cm (30-84") size.

For best results, allow up to 20 cm (8") more for finial and wall clearance.

Watch how to measure

Height

For the best look, mount it about 10 cm (4") above your window frame, or halfway between the frame and the ceiling.

Weight

Rods with a centre support bracket hold light to medium curtains, up to 10 kg (22 lb), when the centre support is installed. This rating does not cover the PINPOINT™ rods, Anywhere or Cappa ADHERA™.

Centre support

If your rod comes with a centre support bracket, install it: it is required to support the full 10 kg (22 lb) weight capacity.

Wall mount

Bracket rods mount on the wall only and come with brackets, screws, drywall anchors and instructions. PINPOINT™ rods fasten into drywall with no drilling, Anywhere is a tension rod that stands between floor and ceiling, and Cappa ADHERA™ uses adhesive brackets.

Choose a rod

Find your style

Pick a style, then the size range that fits your measurement.

Single rods
Hang one set of curtains. Telescoping rods fit a wide range of windows.
Shop single rods
Double rods
Layer two sets of curtains, such as sheers with blackout panels.
Shop double rods
Blackout rods
A wrap-around design keeps curtains flush against the wall, to help stop light leaking in at the sides.
PINPOINT rods
PINPOINT™ mounting is made for drywall: fast, secure installation with minimal wall impact.
Damage-free rods
Anywhere is a tension rod system that sets up damage-free and tool-free. Cappa ADHERA™ installs without compromising your walls.
- Anywhere Curtain Rod & Room Divider
- Cappa Adhera Curtain Rod
Shop Anywhere

How to install

Install your rod

For each rod: what you need, the steps, the video and the instruction sheet (PDF). The steps follow the instruction sheets; the sheet in your box shows every step with drawings.

Cappa and decorative rods
You will need

Pencil, drill with a 6 mm (1/4") bit, screwdriver.
Steps
1. Hold a bracket above the window frame and mark its screw holes with a pencil. Mark every bracket on one level line; sets with three brackets have one in the middle.
2. Drill the marked holes with a 6 mm (1/4") bit.
3. Insert the wall anchors, then screw each bracket to the wall with the screws provided.
4. Rods in three pieces: for a window narrower than 214 cm (84") use two pieces; for a wider window use all three.
5. Unscrew a finial from the rod and feed the curtain onto the rod.
6. Loosen the set screw on each bracket and set the rod in the brackets.
7. Screw the finial back on and tighten the set screws to secure the rod.
Each rod holds up to 10 kg (22 lb); on a double set, 10 kg (22 lb) per rod. The earlier Cappa 1¼" sets use anchors that screw straight into drywall, so they need no drill.
Videos
Instruction sheets (PDF)
Twilight blackout rods
- Twilight Blackout Curtain Rod
- Twilight Double Blackout Curtain Rod
You will need

Pencil, drill with a 6 mm (1/4") bit, screwdriver.
Steps
1. Using a mounting plate as a guide, mark the screw holes on the wall. Mark every plate on one level line; sets with three plates have one in the middle. Make sure the narrow side of the plate is against the wall.
2. Drill pilot holes with a 6 mm (1/4") bit.
3. In drywall, insert the wall anchors and attach each plate with the screws provided. Into a wood stud, use the screws only.
4. Slide the brackets onto the mounting plates.
5. Feed the curtain onto the rod and screw the left end of the rod into the left bracket. On a double set, rest the rods on the middle bracket.
6. Feed the rest of the curtain on and screw the right end of the rod into the right bracket.
7. Wrap and tuck the curtain around both ends so that it hangs flush with the wall.
Videos
- Twilight76-213 cm (30-84") · 168-365 cm (66-144") (video, opens in a new tab)
- Twilight Double76-213 cm (30-84") · 168-365 cm (66-144") (video, opens in a new tab)
Instruction sheets (PDF)
Midnight blackout double rod
- Midnight Blackout Double Curtain Rod
You will need

Pencil, screwdriver.
Follow the instruction sheet: it shows each step with drawings.
Instruction sheets (PDF)
- Midnight107-305 cm (42-120") (PDF, opens in a new tab)
Bellwood, Loop and Ringlet
You will need

Pencil, screwdriver.
Steps
1. Hold the two end brackets and the centre bracket above the window frame on one level line and mark their screw holes with a pencil.
2. Screw the wall anchors into the wall with a screwdriver.
3. Screw the end brackets and the centre bracket to the wall with the screws provided.
4. Slide the curtains onto the rod from both ends.
5. Fit the rod ends to the end brackets and rest the rod in the centre bracket, as the sheet shows.
6. Tighten the screw on the centre bracket.
Each rod holds up to 10 kg (22 lb). Loop: for a window narrower than 193 cm (76"), use two rod pieces; for a wider window, use all three.
Instruction sheets (PDF)
Zen
- Zen Curtain Rod
You will need

Tape measure, pencil, drill with a 6 mm (1/4") bit, screwdriver, mallet.
Steps
1. Measure the window to work out how many rod segments you need; the table on the sheet gives the pieces for each length.
2. Shortest rod: insert a joint into one end segment and gently tap it into place. Connect the other end segment, cover it with the protective cap and tap with a mallet until the segments are snug.
3. Longer rods: add more joints and middle segments the same way and tap them snug. Throw away the cap cover and any unused segments.
4. Screw the finials onto the rod.
5. Using the brackets as a guide, mark the mounting position on the wall.
6. Drill pilot holes with a 6 mm (1/4") bit, insert the anchors if needed, and screw the brackets in place.
7. Feed the curtain onto the rod. Loosen the set screw on each bracket, insert the rod and tighten the set screws.
The rod holds up to 10 kg (22 lb).
Videos
- Zen81-162 cm (32-64") · 162-325 cm (64-128") (video, opens in a new tab)
Instruction sheets (PDF)
- Zen81-325 cm (32-128") (PDF, opens in a new tab)
Anywhere tension rod
- Anywhere Curtain Rod & Room Divider
You will need

No tools needed.
Steps
1. Join the pole sections. Each pole fits a floor-to-ceiling height of 213-304 cm (7-10 ft).
2. Extend the pole up to the ceiling and lock it in place.
3. Set up the second pole the same way, 91-167 cm (36-66") from the first.
4. Feed the curtain onto the rod.
5. Fit the rod ends into the holders on both poles and keep the rod level.
Set it up in a clear area where the poles will not be bumped. Do not lean on the poles or rest anything on them. The floor and ceiling must be smooth and level; avoid thick carpets.
Instruction sheets (PDF)
- Anywhere91-167 cm (36-66") (PDF, opens in a new tab)
PINPOINT rods
PINPOINT™ fastening is made for drywall and installs with no drilling. Standard fasteners are included for surfaces beyond drywall. Watch the video for the steps.
Videos
- PINPOINT rods107-305 cm (42-120") (video, opens in a new tab)
Instruction sheets (PDF)

No instruction sheet is online for these rods yet.

FAQ

Sizing

What rod size do I choose?

Measure the width of your window, including frame, from edge to edge.
Add 20 cm (8") to your window width measurement.

For best results: account for up to 20 cm (8") of additional space for finial and wall clearance.

What height should I install my rod at?

For the best look, mount it about 10 cm (4") above your window frame, or halfway between the frame and the ceiling.

Do I need the centre support bracket?

If your rod comes with one, yes: installation of the included centre support bracket is required to support the full 10 kg (22 lb) weight capacity.

Installation & Hardware

What tools do I need to install my curtain rod?

A tape measure, a pencil and a screwdriver, and for most bracket rods a drill with a 6 mm (1/4") bit. The "You will need" box on your rod's instruction sheet lists the exact tools. Anywhere needs no tools.

Does the rod come with hardware?

Yes. Bracket rods come with brackets, screws, drywall anchors and step-by-step instructions. Cappa ADHERA™ comes with matched adhesive brackets, and Anywhere is a complete tension rod system.

Can I mount the bracket to my ceiling instead of the wall?

The brackets included with our bracket rods are wall-mount only.

Can I shorten or extend my rod to fit my window?

Each rod adjusts in length within its size range; some longer sets come in three pieces. See Install your rod for the steps, videos and instruction sheets.

Rod & Curtain Compatibility

Are the finials removable?

Yes, they simply screw on and off.

Can I swap in my own finials?

Not currently. Our rods are designed to work specifically with the finials they come with.

How much weight can the rod hold?

Are these rods compatible with grommet curtains?

Yes, they work great with grommet-style panels.

Can I use my curtain rod outdoors?

We don't recommend it as these rods were designed and tested for indoor use only.

Curtain rod guide

Measure your window

Height

Weight

Centre support

Wall mount

Find your style

Single rods

Double rods

Blackout rods

PINPOINT rods

Damage-free rods

Shop curtain rods